How to Clean Your Surfboard?

To clean your surfboard, you will need: -A bucket or large container -Warm water

-Mild dish soap -A sponge or soft brush -A towel or cloth

-A surfboard wax (optional) 1. Fill your bucket or container with warm water and add a squirt of mild dish soap. Stir to combine.

2. Submerge your sponge or brush in the soapy water and scrub your surfboard from nose to tail. Pay extra attention to any areas that look dirty or have algae growth. 3. Rinse your board with clean water from a hose, shower, or faucet.

Use a towel or cloth to remove any remaining soap residue. 4. If desired, apply a thin layer of surfboard wax over the entire surface of the board.

  • Rinse your surfboard with fresh water after each use
  • Use a mild soap and soft sponge to clean the board if it is very dirty
  • Avoid using harsh chemicals or abrasives on your surfboard
  • Dry your board completely before storing it away
  • Wax your board regularly to keep it in good condition (optional)

How to clean your surfboard #hack – Courts Council

Homemade Surfboard Cleaner

If you spend any amount of time surfing, you know that your surfboard can get pretty dirty. Whether it’s the salt water, sand, or just general grime, it’s important to keep your board clean. Not only does it look better, but a clean board will also help you stay safe while surfing.

A dirty board can be slippery and difficult to control. There are a lot of commercial surfboard cleaners on the market, but you can also easily make your own at home. All you need is some simple ingredients that you probably already have in your kitchen.

To make your own surfboard cleaner, start by mixing equal parts vinegar and water in a bowl or bucket. You can then add a few drops of dish soap to the mixture if you want. Once everything is mixed together, put it in a spray bottle and apply it to your board.

Let the cleaner sit for a few minutes before scrubbing it off with a sponge or brush. Rinse the board well with fresh water when you’re done cleaning. You can use this same cleaner on other types of boards as well, like paddle boards or skateboards.

It’s gentle enough to use on most surfaces but tough enough to get rid of dirt and grime. Give it a try next time your board needs a good cleaning!

How to Clean Your Surfboard?


What Can I Use to Clean My Surfboard?

When it comes to keeping your surfboard in tip-top shape, regular cleaning is key. But what should you use to clean it? Here are a few options to consider:

1. Fresh water and soap: This is the simplest and most gentle way to clean your surfboard. Just mix up some warm water with a mild dish soap and give your board a good rinse. Be sure to rinse it well afterwards with fresh water to remove any soap residue.

2. Vinegar: For tougher dirt and grime, vinegar can be used instead of soap. Simply mix equal parts vinegar and water together and use it just as you would the soapy mixture above. Again, be sure to rinse well afterwards with fresh water.

3. Baking soda: Baking soda can also be used for tougher stains or spots on your surfboard. Make a paste out of baking soda and water, then apply it directly to the affected area before wiping away with a damp cloth. Rinse well afterwards as usual.

Should You Wash Your Surfboard?

Yes, you should definitely wash your surfboard after every session – even if it doesn’t look dirty! Salt water and sand can both wreak havoc on your board, so it’s important to give it a good cleanse afterwards. Plus, it’s just good hygiene practice in general.

Here’s a step-by-step guide on how to properly wash your surfboard: 1. Rinse off your board with fresh water as soon as you can after surfing. This will help get rid of any salt or sand that may be clinging to the surface.

2. Use a soft sponge or cloth to lightly scrub the entire board, paying special attention to the deck (where you stand) and the fins. You can use a gentle soap if needed, but avoid harsh chemicals or abrasives which could damage the board. 3. Thoroughly rinse off the soap or cleaners with fresh water.

4. Allow your board to air dry completely before storing away – this could take several hours depending on the temperature and humidity levels. Never put away a wet surfboard as this could cause mould or mildew to form.

How Often Should I Clean My Surfboard?

Assuming you’re referring to a fiberglass/polyurethane surfboard, the answer is not as often as you might think. In fact, you can probably get away with cleaning it just once or twice a season – and even less if you’re careful about rinsing it off after each session. Of course, if your board is regularly exposed to salt water, sand, and other abrasive materials, it will need to be cleaned more often.

And if it’s been a while since you gave it a good scrubbing, then by all means go ahead and give it a thorough cleaning. But in general, once or twice per season should suffice. Here’s a quick rundown of how to clean your surfboard:

1) Rinse off the board with fresh water after each session. This will help remove any saltwater, sand, or other debris that may be clinging to the surface. 2) Every few weeks (or as needed), mix up a mild solution of dish soap and water in a bucket.

Use this solution to scrub down the entire surface of the board, paying special attention to areas that tend to collect grime (like the deck pad). Rinse the board thoroughly afterwards. 3) Once every month or so (again, as needed), give your board a deeper clean by using a household cleaner like Simple Green diluted in water.

Scrub down the entire board with this solution and rinse well afterwards – making sure to avoid getting any cleaner on your skin or in your eyes!

How Do I Make My Surfboard Look New?

If your surfboard is looking a little worse for wear, there are some easy ways to make it look new again. First, start by giving it a good wash with soap and water. If there are any stubborn dirt or grime spots, you can use a soft-bristled brush to gently scrub them away.

Rinse the board off well and let it air dry completely before moving on to the next step. Next, you’ll want to sand down the entire surface of the board using medium-grit sandpaper. This will help to smooth out any rough spots and scuffs.

Once you’ve finished sanding, wipe the board down with a damp cloth to remove any dust particles. Finally, apply a fresh coat of wax to the board and buff it until it shines. This will protect the board from future damage and keep it looking like new for longer.

With just a little bit of effort, you can make your old surfboard look brand new again!

Can I Clean My Surfboard With Alcohol?

Yes, you can clean your surfboard with alcohol. It is important to dilute the alcohol though, as undiluted alcohol can damage the surfboard. The ratio of water to alcohol should be 3:1.

You will also want to avoid using rubbing alcohol, as it is too harsh and can damage the surfboard.

Can You Use Windex on a Surfboard?

Windex is a multi-purpose cleaner that can be used on a variety of surfaces, including surfboards. When cleaning a surfboard with Windex, it’s important to first rinse the board with clean water to remove any salt or sand. Then, apply Windex to a clean cloth and wipe down the surface of the board.

Be sure to avoid getting any cleaner on the wax job. Finally, rinse the board again with clean water and dry it off with a towel.


Assuming you want a summary of the blog post titled “How to Clean Your Surfboard” found at, here is a summary: It’s important to clean your surfboard regularly – not only does it help it last longer, but it also prevents you from getting sick. There are two main ways to clean your board: with fresh water and with soap and water.

To clean your board with fresh water, simply rinse it off after every session. If you live in an area with salt water, be sure to rinse with fresh water as soon as possible after surfing. You can also use a pressure washer to remove any stubborn dirt or sand.

To clean your board with soap and water, mix up a solution of mild dish soap and warm water. Use a soft sponge or cloth to scrub the entire surface of your board, paying special attention to the areas where you typically grip the board. Rinse thoroughly and allow the board to air dry completely before storing or using again.